MEM 8902 MOUNTING INSTRUCTIONS

SPORTSHIELD HONDA NRX1800 VALKRYIE RUNE

 

 

TOOLS REQUIRED:  3/16” Allen wrench (provided)

 

1.                  Install the mounting plates onto the windshield using the pre-assembled bolts on the mounting plates. The rubber grommets should be inserted through the holes in the windshield so that the flat round washer part of the grommet lays flat on each side of the windshield. On each plate, get both tabs started before you tighten them.  (see Figure 1.1 & 1.2)

          

             Note:    *(Wide)  – Tabs point in towards each other.

     

2.                  Loosely install the four fork clamps 1-3/4” inches apart. (see Figure 2)

 

3.                  Loosen the four mounting bolts that are to hold the mounting plates to the fork clamps, and slide the mounting plates onto the fork clamps. (see Figure 3)

 

4.                  Adjust the height, angle, and alignment of the shield. Carefully check clearance from steering stop to stop, and tighten all mounting bolts.

 

WARNING:   This is a quick disconnect kit. Always tighten down all mounting bolts after removing or installing the windshield every time.

                        

 

   Fig. 1.1  Left side plate  Fig. 1.2 Right side plate    Fig. 2 fork clamps                           Fig. 3  Plate mounting

1-3/4"              

 

 

Care and Cleaning Instructions

 

To clean your windshield, use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft cloth, such as a T-shirt or flannel cloth. To protect your windshield, please use Novus #2 to remove minor scratches, or use a polish like Memphis Shades Shinola which is specially designed for plastic windshields; glass cleansing agents will cause severe damage to your windshield and will void your warranty.

Never use any glass products, petroleum based chemicals, or cleaning agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake fluid, acetone, and gasoline.

MEM-8902 MOUNTING KIT

SPORTSHIELD HONDA NRX1800VALKYRIE RUNE

 

PART #

DESCRIPTION

QTY.

M8902

MOUNTING INSTRUCTIONS/PARTS LIST

1

M301

1/4" - 20 X 3/8" SS SOCKET HEAD CAP SCREW

4

M302

¼” – 20 X ½” SS SOCKET HEAD CAP SCREW

4

M303

1/4" - 20 X 3/4" SS SOCKET HEAD CAP SCREW

4

M375

P/S ADHESIVE TAPE

4

M313

3/16” SHORT ARM ALLEN WRENCH COVER

1

M314

3/16” T-HANDLE ALLEN WRENCH

1

M337

3/16” T-HANDLE ALLEN WRENCH COVER

1

M310

3/16" SHORT ARM ALLEN WRENCH

1

M523

 LARGE INNER ADJ. FORK CLAMP

4

M522

LARGE OUTER ADJ. FORK CLAMP

4

M505

BUTTON NUT

4

M504

SOCKET SHOULDER WASHER

4

M543

SANTOPRENE GROMMET

4

M501

BEVELED SOCKET WASHER

4

M1055

HONDA NRX1800 RUNE LEFT PLATE -

1

M1056

HONDA NRX1800 RUNE RIGHT PLATE -

1

 

 

FOR MISSING OR REPLACEMENT PARTS OR WARRANTY

INFORMATION CONTACT

 

 

MEMPHIS SHADES

PO BOX 24

COLLIERVILLE, TN 38017

(901) 853-0293

 

VISIT US ON THE WEB AT

www.memphisshades.com

 

 

CUSTOMER SERVICE

customerservice@memphisshades.com