MEM-9913

MEMPHIS FATS/SLIM MOUNTING KIT FOR

HONDA VT1100C3 AERO 98

 

TOOLS REQUIRED: (1) Towel                  (1) 3/16” Allen wrench (provided)

                                      (1) 14mm wrench      (1) 11mm or 7/16 wrench

(1)    8mm wrench

 

Always cover the front fender and gas tank with a towel, in case you drop something.

 

1.                   Using a 14mm wrench, attach the two upper bracket assemblies from the kit to the handlebar bolts underneath the triple tree. The ears should point straight ahead. Do not tighten the nuts until the entire installation is complete, and the windshield has been mounted. If the brackets are improperly aligned it will result in damage to the windshield mounting plates. (See Figure 1)

 

2.                   Using a 8mm wrench, remove the turn signal bar, re-installing it with the lower bracket assembly from the kit, behind it. The ears on the lower bracket should be turned back towards the forks. (See Figure 2)

 

NOTE: The two 6mm Allen screws and washers provided with the kit are only for installing a Fats/Slims windshield in conjunction with a COBRA light bar.

 

3.                   Using the 3/16” Allen wrench, attach the two vertical plates to the upper and lower brackets. The tabs should point away from the headlight.

 

4.          Using the 3/16” Allen wrench provided in the kit, and an 11mm (or 7/16”) wrench, attach the windshield

      to the plates, using the bottom and third bolt up, leaving off the nylon washers. (See Figure 3) You can

              put the 3/16” wrench on your key ring.

 

5.         Tighten the 14mm nuts holding the brackets beneath the triple tree.

 

        Fig. 1 upper bracket mounted          Fig.2 lower bracket mounted          Fig. 3 plate mounted to w/s

                       

 

MEM-9913 MOUNTING KIT

MEMPHIS FATS/SLIM FOR HONDA VT100C3 AERO 98-01

 

Care and Cleaning Instructions

 

To clean your windshield, use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft cloth, such as a T-shirt or flannel cloth. To protect your windshield, please use Novus #2 to remove minor scratches, or use a polish like Memphis Shades Shinola which is specially designed for plastic windshields; glass cleansing agents will cause severe damage to your windshield and will void your warranty.

Never use any glass products, petroleum based chemicals, or cleaning agents with ammonia, bleach or any

Harsh chemicals. This includes Rain-X, Brake fluid, Acetone, and Gasoline.

 

 

 

PART #

DESCRIPTION

QTY.

M913

MOUNTING INSTRUCTIONS/PART LIST

1

M583

HONDA AERO UPPER BRACKET - RIGHT

1

M582

HONDA AERO UPPER BRACKET - LEFT

1

M505

BUTTON NUT

4

M586

RECESSED SPACER WASHER

4

M501

BEVELED SOCKET WASHER

4

M302

1/4” – 20 X 1/2” SOCKET HEAD CAP SCREW

4

M581

HONDA AERO VERTICAL PLATE – RIGHT

1

M580

HONDA AERO VERTICAL PLATE – LEFT

1

M579

HONDA AERO LOWER BRACKET

1

M310

3/16” SHORT ARM ALLEN WRENCH

1

M313

3/16” ALLEN WRENCH HOLDER

1

M324

6mm X 10mm SS SOCKET HEAD CAP SCREW

2

M323

6mm SS WASHER

2

M314

3/16” T-HANDLE ALLEN WRENCH

1

M337

3/16” T-HANDLE ALLEN WRENCH COVER

1

 

FOR MISSING OR REPLACEMENT PARTS OR WARRANTY

INFORMATION CONTACT:

 

Memphis Shades

P.O. BOX 24

COLLIERVILLE, TN 38017

(901) 853-0293

 

VISIT US ON THE WEB AT

www.memphisshades.com

 

 

CUSTOMER SERVICE

customerservice@memphisshades.com