MOUNTING KIT MEM9915
MOUNTING INTRUCTIONS/PARTS LIST FOR
TOOLS REQUIRED: 4MM
ALLEN WRENCH (provided) PHILIPS
SCREWDRIVER #2
6MM ALLEN WRENCH (provided) 3/16”
ALLEN WRENCH (provided)
7/16” WRENCH OR 11MM WRENCH
CAUTION: ALWAYS COVER THE FRONT FENDER AND TANK BEFORE INSTALLATION
1.
Loosely install the windshield mounting plates on
the windshield using the bottom most bolt and the third bolt up on both
sides. The tabs or ears on the plates need
to point away from the headlight
when installed correctly.
Set
it aside for later installation. (See figure 4)
2.
Remove the headlight by extracting the two phillips screws located on the
headlight housing just behind the headlight rim, towards the bottom. (See figure 3 for location)
3.
Unplug the headlight and set it aside for
later re-installation. Extract the three
original 6mm bolts located in the center of the headlight housing. Let the housing rest carefully so that
it doesn’t fall. (See figure 3)
4.
Pull the chrome cover off the front of the turn
signal bar. Remove the turn signal bar
by extracting the original 8mm Allen screws that hold it in place. Let the bar hang freely momentarily, it will
not damage the turn signal wires. (See figure 1 for location)
5.
Install the top of the left side bracket between
the headlight housing and the frame. Use one of the 6mm x 30mm Allen bolts to
hold it loosely in place. To install the bottom of the bracket, use one of the
new 8mm x 45mm Allen bolts provided, place the bolt through the bracket first,
then the spacer, followed by the turn signal bar. (See figure 1)
6.
Repeat the above steps for the right side. (See figure 1)
7.
Once both side brackets are in place and all three
6mm x 30mm bolts are loosely installed in the headlight, tighten down the turn
signal bar bolts first, followed by the three in the headlight. Re-install the chrome cover
on the
turn signal bar. Re-install the headlight and double-check all mounting bolts.
8. To install the windshield, loosen the Allen bolts on the sides of both brackets. Slip the windshield mounting
plates
onto the brackets starting the upper slot first, then slip the bottom slot
in. Adjust the height and angle, and
then tighten down the mounting bolts followed by the windshield bolts. (See figure 5)
NEVER RIDE WITH ANY PART OF THE MOUNTING HARDWARE MISSING OR LOOSE
To clean your windshield,
use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft
cloth, such as a T-shirt or flannel cloth. To protect your windshield, please
use Novus #2 to remove minor scratches,
or use a polish like Memphis Shades Shinola
which is specially designed for plastic windshields; glass cleansing agents
will cause severe damage to your windshield and will void
your warranty.
Never use any glass products, petroleum based chemicals, or cleaning
agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake
fluid, acetone, and gasoline.
MEM9915 MOUNTING KIT
Part #
|
Description
|
Quantity
|
|
M915 |
Instruction
Sheet/Parts List |
1 |
|
M307 |
V-Star
Washer (nylon) |
1 |
|
M329 |
6mm
x 30mm SS Socket Head Cap Screw |
3 |
|
M330 |
8mm
x 45mm SS Flat Head Screw |
2 |
|
M501 |
Beveled
Socket Washers |
4 |
|
M302 |
¼’-20
x ½’ SS Socket Head Cap Screw |
4 |
|
M586 |
Recessed
Spacer Washer |
4 |
|
M544 |
V-Star
Countersunk Spacer |
2 |
|
M605
|
V-Star
Windshield Mounting Plate Left |
1 |
|
M606 |
V-Star
Windshield Mounting Plate Right |
1 |
|
M312 |
4mm
Short Arm Allen Wrench |
1 |
|
M311 |
6mm
Short Arm Allen Wrench |
1 |
|
S1031 |
V-Star
Bracket Assembly Left |
1 |
|
S1032 |
V-Star
Bracket Assembly Right |
1 |
|
M505 |
Button
Nut |
4 |
|
M314 |
3/16”
T-Handle Allen Wrench |
1 |
|
M337 |
3/16”
T-Handle Allen Wrench Cover |
1 |
INFORMATION
CONTACT:
(901) 853-0293
customerservice@memphisshades.com