MEM-9924
FATS/SLIMS MOUNTING HARDWARE
FOR FXSTS/FLSTS SOFTAIL
SPRINGER AND HERITAGE SPRINGER
TOOLS
REQUIRED: 7/16" Wrench 3/16"
Allen wrench (provided)
6MM Allen or 1/4" Allen (Provided) 2 - 9/16" Wrenches
8MM Allen or 5/16" Allen
Always cover the gas tank
and front fender to avoid possible damage during installation.
- Loosely install the windshield mounting plates onto the windshield, using the third bolt up and the bottom most bolt on
both sides of the back of the windshield. The mounting tabs should point away from the headlight when installed properly.
- Remove the 3/8" diameter upper shock mount bolt from the motorcycle; see Figure 1 for the location. Next, locate the original left and right fork mount bolts and remove them as well. Use Figures 1 and 2 for the location.
3. Remove the acorn nut and the aluminum spools from the new stainless rod. Install the new stainless rod provided through the left stainless tri-plate, the acorn nut should be on the same side as the small aluminum spools and the top point of the triangular shape must point upward. Non-heritage models place one of the black spacer washers on the rod after the stainless triangular bracket is in place.
- Slide
the stainless rod through one of the large aluminum spools, then through
the top shock mount. Place the
other large aluminum spool on the front brake side, followed by a black
washer on non-Heritage models, then the right stainless
bracket. (MAKE SURE THAT THE TOP
OF THE TRIANGULAR BRACKETS ARE POINTING UPWARD)
- Install the stainless acorn nut loosely; on non-heritage models re-install the original 5/16" fork mount bolts through the 5/16" slots on the stainless brackets. Heritage models place the black spacer washers in between the stainless bracket and the fork leg. The longer 5/16" screws and flat washers provided must be used on Heritage models. The longer of the two new 5/16" screws goes on the clutch cable side with the cable holders on the outside of the bracket.
- Tighten the 5/16" screws down first, followed by the stainless acorn nuts on the 3/8" rod. Loosen the four mounting points on the small aluminum spools and slip the windshield plates into place. Adjust for angle and tighten all mounting bolts.
Never ride with any hardware
missing or loose, contact
Figure.1 - Left side shown. Upper Shock mount bolt location Left side fork bolt location 
Figure.2 - Right side shown Right side fork bolt location (clutch and brake cable holders)
MEM-9924 MOUNTING KIT
AND
HERITAGE SPRINGER
Part # |
Description |
Quantity |
|
M924 |
Instruction Sheet/Parts
List |
1 |
|
M321 |
5/16" SS Flat Washer |
2 |
|
M331 |
5/16"-24 x 1/2"
SS Socket Head Cap Screw |
1 |
|
M501 |
Beveled Socket Washers |
8 |
|
M302 |
1/4”-20 x 1/2” SS Socket
Head Cap Screw |
8 |
|
M350 |
5/16"-24 x 5/8"
SS Socket Head cap Screw |
1 |
|
M611 |
Large Aluminum Springer
spool |
2 |
|
M707 |
Left Springer Fats/Slims
Mounting Plate |
1 |
|
M708 |
Right Springer Fats/Slims
Mounting Plate |
1 |
|
M345 |
3/8" Stainless Stud |
1 |
|
M337 |
3/16” T-Handle Allen
Wrench Cover |
1 |
|
M314 |
3/16” T-Handle Allen
Wrench |
1 |
|
M311 |
6mm Short Arm Allen Wrench |
1 |
|
M613 |
SS Springer Tri-Plate |
2 |
|
M352 |
3/8" Black Spacer
Washer |
2 |
|
M344 |
3/8"-16 SS Pointed
Acorn Nut |
2 |
|
M612 |
Small Aluminum Springer
Spool |
4 |
Care and Cleaning Instructions
To clean your windshield,
use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft
cloth, such as a T-shirt or flannel cloth. To protect your windshield, please
use Novus #2 to remove minor scratches,
or use a polish like Memphis Shades Shinola
which is specially designed for plastic windshields; glass cleansing agents
will cause severe damage to your windshield and will void
your warranty.
Never use any glass products, petroleum based chemicals, or cleaning
agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake
fluid, acetone, and gasoline.
FOR MISSING OR REPLACEMENT
PARTS OR WARRANTY
INFORMATION CONTACT:
Memphis
(901) 853-0293
VISIT US ON
THE WEB AT