MEM-9927
9”HDLT. FATS/9”HDLT.
SLIMS MOUNTING KIT FOR
(NON-FUEL
INJECTED MODELS)
TOOLS REQUIRED:
(1) Towel (1) 10mm Wrench
(1) 17mm Wrench (1) 3/16" Allen Wrench
(provided)
(1)
Phillips
Screwdriver (1) 7/16" or 11mm
Wrench
(1)
8mm Wrench
1.
Cover the front fender and gas tank with
towels to avoid possible damage during installation.
2.
Remove the headlight lens using a Phillips
screwdriver to remove the two small screws located in the lower part of the
headlight. Unplug the light and
carefully set it aside.
3.
Using a 8mm wrench
and a 10mm wrench, remove the headlight bucket and bracket from the lower
triple tree and set it aside. (See Fig. 1)
4.
Using a 17mm wrench, remove the handlebar
bolt nuts (located under the upper triple tree)(See Fig. 2) and slip the cable holder
off the bolts. Install the upper mounting bracket from the kit (tabs pointing
down), slip the cable holder back onto the bolts and put the nuts back on and
tighten them. Loosen the two mounting
points on the front of the upper bracket so you can install the lower brackets.
5.
Install the two inter-locking lower brackets
using the new 6MM x 40MM longer bolt assemblies provided. These mount under the headlight bracket shown
in figure 1. Slip them into the upper
bracket using the slots at the top.
6.
Re-install the headlight and lens and tighten
all mounting brackets and bolts.
7.
Loosely install the windshield mounting
plates onto the windshield using the lower bolt and the third bolt up. (see fig.3,
8.
Loosen the four mounting points on the
brackets, slip the windshield mounting plates onto the brackets, adjust the
angle and tighten all mounting bolts.
NEVER RIDE WITH ANY HARDWARE MISSING OR LOOSE.
Figure 1 Behind right fork view Figure 2 17mm Handlebar Nuts Figure 3 Mounting plate
tabs
Care and Cleaning Instructions
To clean your windshield,
use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft
cloth, such as a T-shirt or flannel cloth. To protect your windshield, please
use Novus #2 to remove minor scratches,
or use a polish like Memphis Shades Shinola
which is specially designed for plastic windshields; glass cleansing agents
will cause severe damage to your windshield and will void
your warranty.
Never use
any glass products, petroleum based chemicals, or cleaning agents with ammonia,
bleach or any harsh chemicals. This includes Rain-X, brake fluid, acetone, and
gasoline.
MEM9927
MOUNTING KIT
|
PART# |
DESCRIPTION |
QTY. |
|
M927 |
MOUNTING INSTRUCTIONS/PARTS LIST |
1 |
|
M588 |
UPPER BRACKET VULCAN CLASSIC |
1 |
|
M778 |
RIGHT BRACKET VULCAN CLASSIC |
1 |
|
M779 |
LEFT BRACKET VULCAN CLASSIC |
1 |
|
M707 |
LEFT MOUNTING PLATE |
1 |
|
M708 |
RIGHT MOUNTING PLATE |
1 |
|
M501 |
BEVELED SOCKET WASHER |
6 |
|
M302 |
1/4 - 20 X 1/2" SS SOCKET HEAD CAP SCREW |
6 |
|
M586 |
RECESSED SPACER WASHER |
6 |
|
M505 |
BUTTON NUT |
6 |
|
M318 |
6MM X 40MM HEX HEAD CAP SCREW |
2 |
|
M319 |
6MM NYLON INSERT NUT |
2 |
|
M314 |
3/16” T-HANDLE ALLEN WRENCH |
1 |
|
M337 |
3/16” T-HANDLE ALLEN WRENCH COVER |
1 |
|
M313 |
3/16" ALLEN WRENCH COVER |
1 |
|
M310 |
3/16" SHORT ARM ALLEN WRENCH |
1 |
FOR MISSING OR REPLACEMENT PARTS OR WARRANTY
INFORMATION
CONTACT:
Memphis
901-853-0293
VISIT US ON
THE WEB AT