MEM-9933 MEMPHIS SHADES

SPORTSHIELD MOUNTING HARDWARE

FOR FXSTS/FLSTS SOFTTAIL SPRINGER AND HERITAGE SPRINGER

 

TOOLS REQUIRED:                 7/16" Wrench                                                        3/16" Allen wrench (provided)

                                  6MM Allen or  1/4" Allen (Provided)                  2 - 9/16" Wrenches    

                                  8MM Allen or 5/16" Allen

Always cover the gas tank and front fender to avoid possible damage during installation.

 

1      Loosely install the windshield mounting plates onto the windshield. The rubber grommet should be inserted through the holes in the windshield so that the flat round part of the grommet lays flat on both sides of the windshield. The mounting tabs should point away from the headlight cutout when installed properly.

 

  1. Remove the 3/8" diameter upper shock mount bolt from the motorcycle; see Figure 1 for the location. Next, locate the original left and right fork mount bolts and remove them as well. Use Figures 1 and 2 for the location.

 

3.     Remove the acorn nut and the aluminum spools from the new stainless rod.  Install the new stainless rod provided through the left stainless tri-plate, the acorn nut should be on the same side as the small aluminum spools and the top point of the triangular shape must point upward. Non-heritage models place one of the black spacer washers on the rod after the stainless triangular bracket is in place.

 

  1. Slide the stainless rod through one of the large aluminum spools, then through the top shock mount.  Place the other large aluminum spool on the front brake side, followed by a black washer on non-Heritage models, then the right stainless bracket.  (MAKE SURE THAT THE TOP OF THE TRIANGULAR BRACKETS ARE POINTING UPWARD)

 

  1. Install the stainless acorn nut loosely, on non-heritage models re-install the original 5/16" fork mount bolts through the 5/16" slots on the stainless brackets. Heritage models place the black spacer washers in between the stainless bracket and the fork leg. The longer 5/16" screws and flat washers provided must be used on Heritage models. The longer of the two new 5/16" screws goes on the clutch cable side with the cable holders on the outside of the bracket.

 

  1. Tighten the 5/16" screws down first, followed by the stainless acorn nuts on the 3/8" rod.  Loosen the four mounting points on the small aluminum spools and slip the windshield plates into place. Adjust for angle and tighten all mounting bolts.

 

Never ride with any hardware missing or loose, contact Memphis Shades for lost or missing parts.

 

Figure.1 - Left side shown.

 

Upper Shock mount bolt location

 

 

Left side fork bolt location

 

 

Figure.2 - Right side shown

 

Right side fork bolt location

(clutch and brake cable holders)
 


MEM-9933 MOUNTING KIT

SPORTSHIELD FOR SOFTAIL SPRINGER WITHOUT PASSING LAMPS

AND HERITAGE SPRINGER

 

Part #

Description

Quantity

M933

Instruction Sheet/Parts List

1

M321

5/16" SS Flat Washer

2

M331

5/16"-24 x 1/2" SS Socket Head Cap Screw

1

M501

Beveled Socket Washers

8

M302

1/4’-20 x 1/2’SS Socket Head Cap Screw

12

M350

5/16"-24 x 5/8" SS Socket Head Cap Screw

1

M611

Large Aluminum Springer Spool

2

M713

Left Springer Sportshield Mounting Plate

1

M714

Right Springer Sportshield Mounting Plate

1

M345

3/8" Stainless Stud

1

M337

3/16” T-handle Allen Wrench Cover

1

M314

3/16” T-handle Allen Wrench

1

M311

6mm Short Arm Allen Wrench

1

M613

SS Springer Tri-Plate

2

M352

3/8" Black Spacer Washer

2

M344

3/8"-16 SS Pointed Acorn Nut

2

M504

Socket Shoulder Washer

4

M505

Button Nut

4

M543

Santoprene Grommet

4

M612

Small Aluminum Springer Spool

4

 

Care and Cleaning Instructions

 

To clean your windshield, use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft cloth, such as a T-shirt or flannel cloth. To protect your windshield, please use Novus #2 to remove minor scratches, or use a polish like Memphis Shades Shinola which is specially designed for plastic windshields; glass cleansing agents will cause severe damage to your windshield and will void your warranty.

Never use any glass products, petroleum based chemicals, or cleaning agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake fluid, acetone, and gasoline.

FOR MISSING OR REPLACEMENT PARTS OR WARRANTY

INFORMATION CONTACT:

 

Memphis Shades

P.O. Box 24

Collierville, TN  38017

(901) 853-0293

 

Visit us on the web at:

www.memphisshades.com

CUSTOMER SERVICE

customerservice@memphisshades.com