MEM-9941

METRIC *WIDE SPORTS SHIELD

MOUNTING INSTRUCTIONS

 

        TOOLS REQUIRED:  3/16” Allen Wrench  (provided)                           7/16” or 11mm Wrench

 

ALWAYS COVER THE FRONT FENDER AND GAS TANK TO PREVENT ANY POSSIBLE DAMAGE

 

1.    Install the mounting plates on the windshield using the bolts that are pre-assembled on the mounting plates. The rubber grommet should be inserted through the holes in the windshield so that the flat round washer part of the grommet lays flat on each side of the windshield. On each plate, get both tabs started before you tighten them. (See Figure 1.1 & 1.2)                                                                                                                                                                                    

 

                        Note:             *(Wide) - Tabs point towards each other when installed correctly.

                                         

2.    Loosely install the four fork clamps on the forks, approximately two inches apart. (See figure 2)

 

3.       Loosen the four bolts that are to hold the mounting plates to the fork clamps, and slide the mounting plates onto the fork clamps. (See figure 3)

 

4.       Adjust the height, angle, and alignment of the shield. Carefully check gas tank clearance, and tighten all mounting bolts.

 

                  WARNING:  This is a quick disconnect kit.  Always tighten down all mounting bolts after removing

                   or installing the windshield every time                                                               

                                                                                               

Fig. 1.1   Left side plate         Fig. 1.2 Right side plate         Fig.2 Fork clamps         Fig. 3 Shows mounting of plates                                                          

 

 

Care and Cleaning Instructions

 

To clean your windshield, use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft cloth, such as a T-shirt or flannel cloth. To protect your windshield, please use Novus #2 to remove minor scratches, or use a polish like Memphis Shades Shinola which is specially designed for plastic windshields; glass cleansing agents will cause severe damage to your windshield and will void your warranty.

Never use any glass products, petroleum based chemicals, or cleaning agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake fluid, acetone, and gasoline.

 

MEM-9941 MOUNTING KIT

METRIC WIDE SPORTSHIELD

 

PART #

 

DESCRIPTION

QTY.

 

M941

Mounting Instructions/Parts List

1

M797

Left Mounting Plate Fats/Slims

1

M798

Right Mounting Plate Fats/Slims

1

M520

Inner Adj. Fork Clamp

4

M521

Outer Adj. Fork Clamp

4

M504

Socket Shoulder Washer

4

M505

Button Nut

4

M543

Santoprene Grommet

4

M302

¼”-20 x ½” SS Socket Head Cap Screw

8

M301

¼”-20 x 3/8” SS Socket Head Cap Screw

4

M501

 Beveled Socket Washer

4

M561

¼” x ¾” Beveled Spacer Washer

4

M306

¼” – 20 x 5/8” SS Socket Head Cap Screw

4

M314

3/16” T-Handle Allen Wrench

1

M310

3/16” Short Arm Allen Wrench

1

M337

3/16” T-Handle Wrench Cover

1

M313

3/16” Allen Wrench Cover

1

 

 

FOR MISSING OR REPLACEMENT PARTS OR WARRANTY INFORMATION CONTACT:

 

Memphis Shades

 P.O. Box 24

Collierville, TN  38017

(901) 853-0293

 

VISIT US ON THE WEB AT

www.memphisshades.com                                                                                 

 

 

 

CUSTOMER SERVICE

customerservice@memphisshades.com