MOUNTING KIT MEM9943

MOUNTING INTRUCTIONS/PARTS LIST FOR

SPORTSHIELDS FOR V-STAR 650/1100 CLASSIC

 

TOOLS REQUIRED: 4MM ALLEN WRENCH (provided)                                         PHILIPS SCREWDRIVER #2

                                   6MM ALLEN WRENCH (provided)                                          3/16” ALLEN WRENCH (provided)

                                  

 

CAUTION: ALWAYS COVER THE FRONT FENDER AND TANK BEFORE INSTALLATION

 

 

1.      Install the mounting plates onto the windshield using the pre-assembled bolts on the mounting plates. The rubber grommets should be inserted through the holes in the windshield so that the flat round washer part of the grommet lays flat on each side of the windshield. On each plate, get both tabs started before you tighten them. (See figure 4)

 

NOTE:  TABS SHOULD POINT IN TOWARDS HEADLIGHT WHEN INSTALLED PROPERLY

 

2.      Remove the headlight by extracting the two phillips screws located on the headlight housing just behind the headlight rim, towards the bottom. (See figure 3 for location)

 

3.        Unplug the headlight and set it aside for later re-installation.  Extract the three original 6MM bolts located in the center of the headlight housing. Let the housing rest carefully so that it doesn’t fall. (See figure 3)

 

4.      Pull the chrome cover off the front of the turn signal bar.  Remove the turn signal bar by extracting the original 8MM Allen screws that hold it in place.  Let the bar hang freely momentarily, it will not damage the turn signal wires. (See figure 1 for location)

 

5.      Install the top of the left side bracket between the headlight housing and the frame. Use one of the 6MMx30MM Allen bolts to hold it loosely in place. To install the bottom of the bracket, use one of the new 8MMx45MM Allen bolts provided, place the bolt through the bracket first, then the spacer, followed by the turn signal bar. (See figure 1)

 

6.      Repeat the above steps for the right side. (See figure 1)

 

7.      Once both side brackets are in place and all three 6MMx30MM bolts are loosely installed in the headlight, tighten down the turn signal bar bolts first, followed by the three in the headlight.  Re-install the chrome cover

on the turn signal bar. Re-install the headlight and double-check all mounting bolts.

 

8.       To install the windshield, loosen the Allen bolts on the sides of both brackets. Slip the windshield mounting

plates onto the brackets starting the upper slot first, then slip the bottom slot in.  Adjust the height and angle, and then tighten down the mounting bolts followed by the windshield bolts. (See figure 5)

 

NEVER RIDE WITH ANY PART OF THE MOUNTING HARDWARE MISSING OR LOOSE

 

Care and Cleaning Instructions

 

To clean your windshield, use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft cloth, such as a T-shirt or flannel cloth. To protect your windshield, please use Novus #2 to remove minor scratches, or use a polish like Memphis Shades Shinola which is specially designed for plastic windshields; glass cleansing agents will cause severe damage to your windshield and will void your warranty.

Never use any glass products, petroleum based chemicals, or cleaning agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake fluid, acetone, and gasoline.

 

 

 

MEM9943 MOUNTING KIT

 V-STAR 650/1100 CLASSIC SPORTSHIELD

 

 

Part #

Description

Quantity

M943

Instruction Sheet/Parts List

1

M307

V-Star Washer (nylon)

1

M329

6mm x 30mm SS Socket Head Cap Screw

3

M330

8mm x 45mm SS Flat Head Screw

2

M501

Beveled Socket Washers

4

M302

¼’-20 x ½’ SS Socket Head Cap Screw

8

M586

Recessed Spacer Washer

4

M544

V-Star Countersunk Spacer

2

M1015

 Mounting Plate Left

1

M1016

Mounting Plate Right

1

M312

4mm Short Arm Allen Wrench

1

M311

6mm Short Arm Allen Wrench

1

S1031

V-Star Bracket Assembly Left

1

S1032

V-Star Bracket Assembly Right

1

M504

Socket Shoulder Washer

4

M543

Santoprene Grommet

4

M505

Button Nut

8

M314

3/16” T-Handle Allen Wrench

1

M337

3/16” T-Handle Allen Wrench Cover

1

 

 

FOR MISSING OR REPLACEMENT PARTS OR WARRANTY

INFORMATION CONTACT:

 

 

Memphis Shades

 P.O. Box 24

Collierville, TN  38017

(901) 853-0293

 

VISIT US ON THE WEB AT

www.memphisshades.com

 

CUSTOMER SERVICE

customerservice@memphisshades.com