MOUNTING KIT MEM9944
MOUNTING
INTRUCTIONS/PARTS LIST FOR
SPORTSHIELDS FOR ROADSTAR
TOOLS REQUIRED: 8MM
WRENCH PHILIPS
SCREWDRIVER #2
6MM ALLEN WRENCH (provided) 3/16”
ALLEN WRENCH (provided)
CAUTION: ALWAYS COVER THE FRONT FENDER AND TANK BEFORE INSTALLATION
1. Install the mounting plates onto the windshield using
the pre-assembled bolts on the mounting plates. The rubber grommets should be
inserted through the holes in the windshield so that the flat round washer part
of the grommet lays flat on each side of the windshield. (See figure 4)
NOTE: TABS
SHOULD POINT IN TOWARDS HEADLIGHT WHEN INSTALLED
2. Remove the headlight by
extracting the two phillips
screws located on the headlight housing just behind the headlight rim, towards
the bottom. (See
figure 3 for location)
3. Unplug the headlight and set
it aside for later re-installation.
Extract the three original 6MM bolts located inside the headlight
housing. Remove the washers from the top
two bolts and install them on the new 6MMx30MM screws provided. Let the housing rest carefully so that it
doesn’t fall. (See
figure 2 for bolt location)
4. Pull the chrome cover off
the front of the turn signal bar. Remove
the turn signal bar by extracting the original 8MM Allen screws that hold it in
place. Let the bar hang freely
momentarily, it will not damage the turn signal wires.
5. Install the top of the left
side bracket between the headlight housing and the headlight bracket. Use one
of the 6MMx30MM Allen bolts to hold it loosely in place. To install the bottom
of the bracket, use one of the new 8MMx45MM Allen bolts provided, place the
bolt through the bracket first, then the countersunk spacer, followed by the
turn signal bar.
6. Repeat the above steps for
the left side. (Ref. figure 1)
7. Once both brackets are in
place and the new 6MMx30MM bolts are loosely installed. Loosely re-install the original lower bolt
inside the headlight housing, tighten down the turn signal bar bolts first,
followed by the three in the headlight.
Re-install the headlight and double-check all mounting bolts.
*NOTE: With this installation the turn signal bar
cover does not fit properly, it is recommended
to not re-install the turn
signal bar cover.
8. To install the windshield,
loosen the four Allen screws on the sides of both brackets. Slip the windshield
mounting plates onto the brackets starting the upper slot first, then slip the bottom slot in. Adjust the height and angle. Tighten down the mounting bolts followed by
the windshield bolts.(See Figure 4)
NEVER RIDE WITH ANY PART OF THE MOUNTING HARDWARE
MISSING OR LOOSE
To clean your windshield,
use only warm water and a mild non-abrasive, dishwashing liquid. Use a soft
cloth, such as a T-shirt or flannel cloth. To protect your windshield, please
use Novus #2 to remove minor scratches,
or use a polish like Memphis Shades Shinola
which is specially designed for plastic windshields; glass cleansing agents
will cause severe damage to your windshield and will void
your warranty.
Never use any glass products, petroleum based chemicals, or cleaning
agents with ammonia, bleach or any harsh chemicals. This includes Rain-X, brake
fluid, acetone, and gasoline.
MEM-9944 MOUNTING KIT
ROADSTAR SPORTSHIELD
Part #
|
Description
|
Quantity
|
|
M944 |
Instruction Sheet/Parts
List |
1 |
|
M329 |
6mm x 30mm SS Socket Head
Cap Screw |
2 |
|
M330 |
8mm x 45mm SS Flat Head
Screw |
2 |
|
M501 |
Beveled Socket Washers |
4 |
|
M586 |
Recessed Spacer Washer |
4 |
|
M544 |
RoadStar Countersunk
Spacer |
2 |
|
M1017 |
Mounting Plate Left |
1 |
|
M1018 |
Mounting Plate Right |
1 |
|
M337 |
T-Handle Allen Wrench
Cover |
1 |
|
M314 |
3/16” T-Handle Allen
Wrench |
1 |
|
M311 |
6mm Short Arm Allen Wrench |
1 |
|
S1079 |
RoadStar Bracket Assembly
Left |
1 |
|
S1080 |
RoadStar Bracket Assembly
Right |
1 |
|
M302 |
1/4-20x1/2" SS Socket
Head Cap Screw |
8 |
|
M504 |
Socket Shoulder Washer |
4 |
|
M543 |
Santoprene Grommet |
4 |
|
M505 |
Button Nut |
8 |
FOR REPLACEMENT OR MISSING PARTS OR WARRANTY
INFORMATION CONTACT:
(901) 853-0293
VSIT
customerservice@memphisshades.com